VZ-61 FRT – 12-pack Forced Reset Trigger designed exclusively for VZ-61 / Skorpion builds using a TORTORT receiver. Manufactured from PET-CF for testing, spares, and multi-setup use.
VZ-61 FRT 6 PACK | TORTORT RECEIVER ONLY (PET-CF)
TORTORT Receiver Exclusive — PET-CF 12 Pack
PRODUCT DETAILS
Forced Reset Trigger for the vz. 61 Skorpion platform.(TORTORT receivers only).
This FRT has been confirmed to function in our testing on TORTORT receivers.
That does not guarantee the same result in every firearm. Individual receiver units vary.
If it does not function in your setup, that is not a defect and is not grounds for a refund, return, or exchange.
All sales are final on function and compatibility.
Manufactured from PET-CF (carbon fiber reinforced polyester), offering a strong, lightweight, heat-resistant option for functional use, experimentation, and replacements.
This design allows for a fast, consistent trigger reset while maintaining proper semi-automatic function.
Minor fitting and tuning may still be required depending on your specific build.
WHAT YOU GET
- (12x) VZ-61 FRT — PET-CF (Carbon Fiber Reinforced)
Sold as a 6-pack for testing, fitment, spares, and extended use.
COMPATIBILITY
Designed for:
- VZ-61 / Skorpion platforms using a TORTORT receiver
Not compatible with:
- Non-TORTORT aftermarket receivers
- Clone receivers with different pin, pocket, or fire-control geometry
Buyer is responsible for confirming they have a TORTORT receiver before purchase.
MATERIAL DETAILS
PET-CF is a carbon fiber reinforced filament known for:
- High strength-to-weight ratio
- Heat resistance
- Durability in functional firearm components
PET-CF parts are considered consumable. Lifespan will vary by use, fitment, ammo, and setup.
INSTALLATION NOTES
To install, pop the safety out, slide it over the end, pop the safety back in.
No additional installation assistance is provided.
If you need help, consult a qualified gunsmith.
Installation may require:
- Minor fitting in the smaller of the two cylinders
- Adjustment to prevent trigger binding
- Tuning for reliable function
Results will vary depending on platform tolerances and configuration.
Basic mechanical experience is strongly recommended.
FITMENT
Fitting/tuning may be required for functionality.
The hole that fits over the selector was purposely made a bit small, due to variations in different selectors the hole was left tight so it can be fit to each individual selector, open the hole until it moves freely but does not have excess side to side movement. A rolled up piece of sandpaper can be used to slowly open up the hole for the perfect fit.
In some setups you will need to remove the full auto catch off of the hammer, very simple to do with an angle grinder, belt sander or dremel – see photo
In some setups you will need to round off the full auto trip on the bolt. On some of the bolts the edge can be pretty sharp and this will dig into the frt and cause function issues – see photo
IMPORTANT INFORMATION
- This product is exclusive to TORTORT receivers
- Not all setups will perform identically
- Results depend on correct installation and configuration
- No installation support beyond what is on this page is provided
Due to the nature of this product:
- All sales are final
- No refunds for installation, function, or receiver mismatch
- No returns or exchanges on used or installed items
DISCLAIMER
All 3D printed parts are sold as-is. Due to manufacturing and material variability, performance and lifespan are not guaranteed. No refunds, exchanges, or returns on used or installed items. By purchasing you accept these terms and use the parts at your own risk.
This design is based on the original “VZ 61 BRRRT” concept by designer “justaguy”.
COMPATIBILITY / SEARCH TERMS
VZ-61 FRT
VZ61 FRT
VZ 61 FRT
Skorpion FRT
Scorpion FRT
vz 61 forced reset trigger
TORTORT FRT
TORTORT Skorpion FRT
vz 61 FRT 12 pack
Skorpion trigger upgrade
