VZ-61 FRT 12 Pack – PET-CF Forced Reset Triggers for the vz. 61 Skorpion platform. Confirmed on Czechpoint, Titus, 3D-printed, and rewelded receivers.
VZ-61 SKORPION FRT (PET-CF 12-PACK)
Experimental / Beta Release
PRODUCT DETAILS
CZECHPOINT / TITUS / 3D-PRINTED / REWELD COMPATIBLE — BETA
VZ-61 FRT 12 Pack – PET-CF Forced Reset Triggers for the vz. 61 Skorpion platform.
This FRT has been confirmed to function in our testing on Czechpoint, Titus, printed, and rewelded receivers.
That does not guarantee the same result in every firearm. Receiver makers and individual units vary.
If it does not function in your setup, that is not a defect and is not grounds for a refund, return, or exchange.
All sales are final on function and compatibility.
May also work on other vz. 61 pattern firearms with a similar fire control group.
Manufactured from PET-CF (carbon fiber reinforced polyester), providing a strong, lightweight, heat-resistant option for functional use, experimentation, and setup refinement.
This design allows for rapid trigger reset while maintaining proper semi-automatic function in compatible setups.
This 12-pack is intended for testing, multiple setups, spares, and fitment flexibility.
Note: Some setups may require light fitting in the smaller of the two cylinders to prevent the trigger from binding.
This is not a guaranteed drop-in on every vz. 61 clone. Fitting/tuning may be required depending on your specific receiver and fire control group.
WHAT YOU GET
- (12x) VZ-61 Skorpion FRT — PET-CF (Carbon Fiber Reinforced)
COMPATIBILITY
Designed for:
- vz. 61 / Sa vz. 61 Skorpion pattern platforms
- Czechpoint receivers — confirmed
- Titus receivers — confirmed
- 3D-printed receivers — confirmed
- Rewelded receivers — confirmed
- Other vz. 61–pattern firearms with a similar fire control group
Important: Verify your fire control group matches the configuration shown in the product photos before purchasing. Individual unit tolerances can still require fitting.
MATERIAL DETAILS
This product is manufactured from PET-CF, a carbon fiber reinforced polyester known for:
- High strength-to-weight ratio
- Good durability under repeated use
- Increased heat resistance compared to standard polymers
Provides a lightweight alternative while remaining suitable for functional components.
INSTALLATION NOTES
To install, pop the safety out, slide it over the end, pop the safety back in.
No additional installation assistance is provided.
If you need help, consult a qualified gunsmith.
Installation may require:
- Minor fitting in the smaller of the two cylinders
- Adjustment to prevent trigger binding
- Tuning for reliable function
Results will vary depending on platform tolerances and configuration.
Basic mechanical experience is strongly recommended.
FITMENT
Some setups may need light fitting in the smaller of the two cylinders to prevent the trigger from binding.
This is NOT a guaranteed drop-in on every vz. 61 clone.
Fitting/tuning may be required for functionality.
The hole that fits over the selector was purposely made a bit small, due to variations in different selectors the hole was left tight so it can be fit to each individual selector, open the hole until it moves freely but does not have excess side to side movement. A rolled up piece of sandpaper can be used to slowly open up the hole for the perfect fit.
In some setups you will need to remove the full auto catch off of the hammer, very simple to do with an angle grinder, belt sander or dremel – see photo
In some setups you will need to round off the full auto trip on the bolt. On some of the bolts the edge can be pretty sharp and this will dig into the frt and cause function issues – see photo
IMPORTANT INFORMATION
- This is a beta product
- Not all setups will perform identically
- Functionality has been confirmed on Czechpoint, Titus, 3D-printed, and rewelded receivers when properly fitted
- No installation assistance is provided beyond the information on this page
- If additional help is needed, consult a qualified gunsmith
Due to the nature of this product:
- All sales are final
- No refunds will be issued based on installation or functionality issues under any circumstances
- No refunds, exchanges, or returns on used or installed items
ADDITIONAL NOTES
All 3D printed parts are considered consumable and are sold as-is. Due to manufacturing and material variability, performance and lifespan are not guaranteed. By purchasing, you accept these terms and use the product at your own risk.
This design is based on the original “VZ 61 BRRRT” concept by designer “justaguy”.
COMPATIBILITY / SEARCH TERMS
VZ-61 FRT
VZ61 FRT
VZ 61 FRT
Sa vz. 61 FRT
Skorpion FRT
Scorpion FRT
vz 61 forced reset trigger
Czechpoint Skorpion FRT
Titus Arms FRT
CSA Skorpion FRT
vz 61 FRT 12 pack
Skorpion trigger upgrade
